Washington State Journeyman Practice Test

These questions are part of the practice quiz. Start practicing

• What is required in addition to renewal requirements when applying for a General or Specialty exam?
• What occurs during a short circuit?
• Which component is most directly responsible for protecting against overload in a circuit?
• What thickness of steel plate is required to protect Type NMC cable installed in shallow chases?
• Listed tamper-resistant receptacles are required at which of the following locations?
• Electrical Plan Review is not required for which modification criteria?
• What is a receptacle in electrical terms?
• What is a key requirement for a visual and audible alarm in on-site sewage systems?
• What additional compliance must flexible cord and cord connections for electric discharge luminaires meet, according to WAC?
• What should be done if an electrical task exceeds standard limitations?
• If cited for a violation, what is the maximum amount you need to send for an appeal, according to RCW?
• What type of cable is commonly used for residential wiring in Washington State?
• How often should service disconnects be accessible for use?
• What is the primary function of a transformer?
• What is the purpose of arc-fault circuit interrupters (AFCIs)?
• What temperature correction factor is used for voltage calculation in photovoltaic systems?
• What is the primary limitation of the 06B specialty compared to the 06A specialty?
• What labeling must telecommunications service providers indicate at termination points?
• What is the risk associated with poor wiring practices?
• Who can grant a variance for electrical work?
• What document provides the guidelines for voltage correction factors for photovoltaic modules?
• What must electrical plans submitted for review include?
• What is the role of circuit articulation in power distribution?
• Which RCW article covers the examinations and fees for electrical administrator certificates?
• Which of the following best describes a journeyman electrician?
• What is NOT a primary purpose of Electrical Plan Review?
• Which of the following does NOT fall under the requirements of NEC 410.56E?
• What does NEC stand for in the context of electrical codes?
• What does a surge protector do?
• What determines the weight rating of a ceiling box?
• What should the maximum voltage for a photovoltaic system in Washington State comply with?
• What does NEC stand for in electrical terminology?
• How is a circuit used for construction classified?
• What is the recommended action if an electrical outlet is sparking?
• If an overcurrent device is replaced in a panelboard located over steps, what is the status of the installation?
• What is the minimum distance a power line should be from a swimming pool?
• What is allowed for lawfully installed existing electrical installations that do not comply with the current code?
• What is the function of a circuit interrupter?
• What type of alarm must on-site sewage disposal systems with pumps have?
• When may a trainee work without direct supervision, according to RCW standards?
• Which of the following is considered serious noncompliance?
• What safety feature is required in basement or outdoor outlets?
• Where can requirements for wiring methods and materials be found in the WAC codes?
• What does “load calculation” refer to in electrical systems?
• What size circuit modifications does NOT require an Electrical Plan Review?
• Which of the following is not considered serious noncompliance?
• What is Ohm's Law?
• Which type of receptacles does the GFCI requirement not apply in specific conditions?
• When a ground resistance test is not performed, how far apart must two or more electrodes be installed?
• Where must a journeyman or trainee certification card be displayed?
• Which of the following does NEC emphasize regarding electrical safety?
• Water heaters with a rated circuit load exceeding 3500 watts must utilize branch circuit conductors of at least what size copper?
• What is necessary for a receptacle located near swimming pools?
• Which is not a minimum safety requirement for residential buildings wired in Canada and moved into Washington?
• When must a service disconnect be accessible?
• Who is required to have an electrical license according to the RCW?
• What is the minimum height for lettering on an emergency disconnecting button for fuel dispensers?
• How far must a flammable-liquid or oil-filled transformer be mounted from a combustible building surface?
• What does the term "grounding" refer to in electrical systems?
• What does "overcurrent protection" refer to?
• What type of grounding electrode must be used at each new building or structure on a permanent concrete foundation?
• Who is responsible for producing the affidavit of experience form for a trainee?
• What type of receptacle must be installed for portable or mobile electric signs?
• The responsibility of managing electrical inspections is primarily under which authority?
• When must a trainee return the form issued by the inspector after being found without supervision?
• What determines the height for the center of the service meter on a Service Entrance?
• What is referred to as a "service entrance" in electrical terms?
• What is the required experience before applying for the journeyman exam in Washington State?
• What must be visibly displayed to legally perform electrical work?
• An electrical/telecommunications contractor's license is valid for how long?
• What must be present if service conductors are smaller than the overcurrent protection for installations other than one- and two-family dwellings?
• What is the role of a licensed electrician?
• What is the appropriate method for securing cables in walls?
• Where is Electrical Metallic Tubing (EMT) prohibited from being installed, according to WAC?
• Who has the authority to order the discontinuance of electrical service for non-compliance with RCW?
• When is it necessary to use a junction box in electrical work?
• According to NEC code, how must power limited Class 2 and Class 3 cables be secured in a suspended ceiling?
• How far from the outside edge of a peninsular countertop must a receptacle be located?
• In what locations may Tray Cable be used if all installation requirements are met?
• What is meant by the term "imminent danger" in relation to serious violations?
• What is a benefit of using conduit for electrical wiring?
• What is the permitted minimum clearance between conductors for outside overhead spans not exceeding 300 volts?
• What is the minimum fine a worker must pay when appealing a violation?
• What must be part of a project installer’s documentation for larger installations?
• What is the main goal of on-the-job training for electricians?
• What is the role of an electrical inspector?
• What is one requirement to obtain an original administrator certificate?
• What is the maximum number of allowed ampacity for a General Electrical electrician?
• To whom does the exemption apply when working on their own property and in specific situations?
• For electrical plans, what is NOT required to be shown?
• What is the minimum headroom clearance required for electrical panels?
• What is the main function of a circuit breaker?
• How many days after expiration can a person renew their electrician certificate without reexamination?
• What does the department classify as "serious violations"?
• What is the primary purpose of using GFCI outlets?
• Which type of circuit is specifically designed to protect sensitive electronics?
• What is NOT required by the National Electrical Code for motors?
• What code establishes the standards for electrical installations in Washington State?
• What happens if the voltage drop exceeds the NEC recommended limits?
• To qualify for the General Journey Level Exam, how many in-class education hours are required for the 8000-hour certification?
• What does 'low voltage' mean according to NEC standards?
• What is the relevant RCW code for general rules regarding Emergency Systems?
• What must an inspector issue if a trainee is found working without supervision?
• A disconnecting means must be marked by what?
• What is the minimum number of NEC hours required for Continuing Education?
• Unless specified by manufacturer instructions, what gauge of copper should be used to bond natural gas piping?
• Within how many days must a party appeal a penalty issued by the department?
• What is a common purpose of circuit breakers?
• What is the typical wire size used for general-purpose branch circuits in residential installations?
• What must be capable of isolating each dispenser individually from all external voltage sources?
• What is the significance of NEC Code revisions?
• How will industrial control panels be determined to meet minimum electrical safety standards?
• How long is the accreditation period for Professional Engineers approved by the department?
• How often must an electrical journeyman renew their license in Washington State?
• What is meant by the term “feeder” in electrical terminology?
• What is the difference between a grounding conductor and a bonding conductor?
• How far back can an electrical audit cover prior to the last affidavit verifying training hours?
• What type of personal protective equipment (PPE) is recommended for electrical work?
• When can a building use the Washington state energy code in lieu of NEC 220.12 for lighting load calculations?
• How is the capacity of a fuse determined?
• What is the voltage drop limit in branch circuits according to NEC?
• If a worker commits a serious violation of the RCW, what can happen to their certification?
• What happens if a contractor does not comply with record-keeping requirements?
• What is the fine for the first offense of performing electrical work without a valid certificate of competency?
• What is a critical component of Electrical Plan Review?
• What kinds of devices are typically used for overcurrent protection?
• What work can a General Electrical (01) certified electrician perform?
• How close must multiple outside feeder disconnecting means be grouped from each other?
• What maximum voltage is associated with the 06B specialty?
• How should flexible cords be utilized according to electrical code?
• What is a requirement for labeling an emergency disconnect button?
• What action can lead to criminal prosecution when applying for a certification?
• What is the primary purpose of the Washington State Journeyman exam?
• What safety equipment is essential when working on live electrical systems?
• How many business days must an employer provide trainee records for inspection upon request?
• What is defined as “ampacity”?
• To qualify for a 4000-hour specialty, how many hours of Basic Classroom Education courses must an applicant complete?
• What does the term “ampacity” refer to?
• What is the required distance for supervision of specialty electrical trainees when outdoors?
• Which activity is NOT exempt from holding a valid electrical contractor license?
• Which type of transformers require specific installation distances from building surfaces?
• According to the RCW, which of the following is NOT required to legally gain hours as a trainee?
• Under what condition are pumping chambers for sewage considered unclassified?
• What is one requirement for outdoor electrical installations?
• What should be done before starting electrical work?
• For which of the following reasons can an electrical certificate be revoked?
• What can reduce the 5-foot separation requirement from a swimming pool?
• What type of current does Ohm's Law apply to?
• Which of the following best describes the term "ampacity"?
• What is the purpose of a circuit breaker?
• What are multi-wire branch circuits?
• Why is it important to consult local codes for electrical work?
• Where must an identification plate stating "Service conductor ampacity" be installed?
• Where in a home are "wet locations" commonly found?
• What indicates that a product was produced in compliance with appropriate standards?
• What does the term “voltage” refer to in electrical terminology?
• In a garage or unfinished basement, how must a red receptacle supplying a fire alarm system be identified?
• What determines the examination fee for a Journeyman or Specialty Electrician?
• What aspect does the electrical Plan Review NOT concern itself with?
• What type of cord must be used for the electric discharge luminaires as per WAC?
• When are junction boxes required in electrical installations?
• What is required for a temporary service installation?
• What signifies a red receptacle with a red cover plate in a garage?
• What is the minimum size for U-bolts on a Service Mast that is not over 26" high?
• What color must device and junction boxes for fire alarm systems be?
• Field installed electrical equipment must be located at least how many feet from the swimming pool?
• How is a receptacle outlet defined?
• How are conductors typically sized for residential service?
• What cannot a factory-trained technician perform when working with electrical/telecommunication equipment?
• What is the function of the ground-fault circuit interrupter (GFCI) test button?
• What is the minimum distance a flammable-liquid or oil-filled transformer must be installed from a non-combustible surface?
• Which individual is required to ensure compliance with safety laws in the firm?
• How far from the machine room door must elevator main line disconnects be located?
• For setting a manufactured or mobile building, it is considered work on a ______.
• For projects larger than what capacity must an installer provide a one-line diagram before inspection approval?
• What type of wiring requires additional protection in damp or wet locations?
• Which document outlines the scope of work for electricians in Washington State?
• What is the purpose of a main bonding jumper?
• How long is a trainee certification valid before it needs to be renewed?
• Is a permit needed for the "like-in-kind" replacement of a feeder circuit breaker?
• How often should electrical equipment be inspected for safety?
• What must be considered regarding pendant boxes and flexible cord connections?
• Which of the following is NOT a reason for grounding electrical systems?
• What does the acronym NEC stand for in the context of electrical standards?
• Why is proper circuit labeling important?
• Which type of electrical installation typically requires a higher gauge of conductors?
• When is a permit required for electrical work?
• What is the Continuing Education requirement for a certified electrician to renew their certification?
• Why is using appropriate wire insulation important?
• What information must be submitted to obtain an original administrator certificate?
• According to regulations, motors are exempt from being what?
• What is the requirement for GFCI protection for RV supply power receptacles?
• How many uncertified individuals can a certified electrician supervise?
• What is the purpose of a grounding electrode system?
• Who is responsible for inspecting mobile homes for modifications of electrical circuits?
• What must be true about the design of emergency and standby systems in industry?
• What is the inspection fee for the first 1300 square feet of a new single-family dwelling?
• When renewing a training certificate, what must be submitted within 180 days of the renewal date?
• What is one of the primary duties of an Electrical Administrator according to the RCW?
• If the product safety standard is not ANSI, what must happen?
• What is the primary purpose of grounding in electrical systems?
• What does the scope of work for a 07-specialty electrician exclude?
• What should be done if an electrical panel shows signs of overheating?
• What is the function of a lightning arrestor?
• For an electrical work related fine policy, what is the amount specified for subsequent offenses?
• A breaker panel that has been submerged in water must be ______.
• What is required for floating buildings in relation to service rated disconnects?
• What materials are typically used for grounding electrode systems?
• Which of the following could lead to overheated wiring?
• What is the status of permits when an electrical utility or its contractor works on utility systems?
• What might be a consequence of lying to the department?
• The HVAC/Refrigeration specialties may replace a disconnecting means enclosure for equipment rated not more than what?
• Which is a common cause of electrical fires?
• What are load centers used for in electrical systems?
• Which type of electrical box is used specifically for fixture mounting?
• If a false statement is made on an affidavit of experience, how many hours can the department deduct?
• Which electrical specialty is fully explained in the RCW but only listed in the WAC?
• How must a receptacle in a wall countertop space serve contiguous peninsular countertop space?
• What type of certificate is issued to applicants who are visually impaired and require assistance during the exam?
• How can installation errors lead to fire hazards?
• Which statement regarding lighting branch circuit conductors is true according to NEC?
• Where can you find the rules for non-conforming installations according to the RCW?
• What is one possible consequence of being judged incompetent to work in the electrical trade?
• What is the minimum age requirement to take the Washington State Journeyman exam?
• Is it required for interconnected electrical power production sources to be grouped with service disconnecting means?
• What must the emergency disconnecting means or operator simultaneously disconnect when serving gasoline or volatile flammable liquids?
• How many inspections are allowed for a plant that uses 5 electricians?
• What is the maximum depth for underground electrical installations in Washington State?
• In healthcare facilities, to what do the GFPE protection requirements apply?